Quick answer: Put a penny into a main tread groove with Lincoln’s head pointing down. If you can see the top of his head, your tread is at or below 2/32 inch — the legal minimum in most US states — and the tire needs replacing now. For a safer, earlier warning, use a quarter instead: if you can see the top of Washington’s head, you are at or below 4/32 inch and should start shopping for new tires. The whole check takes about two minutes per tire, costs nothing, and needs no tools.
Your tires are the only part of your car that touches the road, and your brakes and steering depend on those four patches of rubber gripping the pavement.
Tread grooves channel water away so the rubber stays in contact with the road. As they wear shallow, the tire starts riding on a film of water instead of cutting through it — that is hydroplaning — and stopping distances stretch out, well before a tire looks bald. Checking tread depth takes two minutes, and a coin, the wear bars already in your tires, or a cheap gauge will give you a clear answer.
What Is Tire Tread Depth?
Tire tread depth is the height of the tread rubber measured from the bottom of a main groove to the top of the tread surface. In the United States it is measured in 32nds of an inch, which is why you will see numbers like 10/32, 6/32, and 2/32. A reading of 6/32 inch means six thirty-seconds of an inch of tread remains above the bottom of the groove.
Most new all-season passenger tires start at 10/32 to 11/32 inch (about 8 to 9 mm). Winter and all-terrain tires often start deeper; some high-performance summer tires start a little shallower, around 8/32 to 10/32 inch.
Two numbers matter more than any others. 2/32 inch (about 1.6 mm) is the legal minimum in most US states. At this depth the tire is legally worn out, will fail a safety inspection in states that have one, and must be replaced. The National Highway Traffic Safety Administration (NHTSA) advises replacing tires once tread reaches 2/32 inch.
4/32 inch (about 3.2 mm) is the smart replacement point. At this depth your tires are still legal, but wet-weather performance has already fallen sharply. In AAA testing, tires worn to 4/32 inch needed an average of 87 extra feet to stop from 60 mph on wet pavement — 43% more distance — and lost about a third of their wet handling.
That gap between “legal” and “safe” is the key idea here: the penny test marks the legal floor, the quarter test marks the safety line. Use the quarter test to decide, and the penny test as your deadline.
Before You Start
Get three things right first, or a quick check can give you a false sense of security.
Park on flat ground and set the parking brake. For a front tire, turn the steering wheel outward so you can see the tread face more easily.
Measure the main grooves, not the small slits. The wide channels that run around the tire are the main grooves — those are what you measure. The thin cuts across the tread blocks are called sipes, and they will give you a meaningless reading.
Check more than one spot, and go by the lowest number. Tires almost never wear evenly — the inside edge can be bald while the center looks fine. A tire is only as good as its most worn point, so use the shallowest reading you find on any of the four tires.
The 4 Ways to Check Tire Tread Depth, Compared
| Method | Cost | What it checks | Accuracy |
|---|---|---|---|
| Penny test | Free | 2/32 inch (legal limit) | Pass or fail only |
| Quarter test | Free | 4/32 inch (replace-soon line) | Pass or fail only |
| Wear bars | Free, built into the tire | 2/32 inch (legal limit) | Pass or fail only |
| Tread depth gauge | About $3–$10 | Any depth, in 32nds of an inch | Exact number |
If you only have two minutes, do the quarter test first — it is the more useful coin test. If you want to track wear over time, buy a gauge: it is the only method that gives you a real number to compare next month.
Method 1: The Penny Test (Checks 2/32 Inch)
The penny test is the classic check, and NHTSA itself recommends it. It works because the distance from the edge of a US penny to the top of Lincoln’s head is almost exactly 2/32 inch — the legal minimum tread depth.
Step 1: Hold the penny with Lincoln’s head pointing down, upside down and facing you.
Step 2: Push it into a main tread groove — one of the wide channels that runs around the tire, not a sipe or a shoulder block. Push it as far down as it will go.
Step 3: Look at how much of Lincoln’s head you can see. If the tread covers the top of his head, you have more than 2/32 inch left. If you can see all of his head, your tread is at or below 2/32 inch. The tire is legally worn out and needs replacing now.
Step 4: Repeat in several grooves on all four tires and go by the shallowest result you find anywhere.
The penny test has one honest limitation: it is a pass/fail check at the legal minimum, not a measurement. It cannot tell you whether you have 8/32 inch or 3/32 inch left — only whether you have crossed the 2/32 line.
Method 2: The Quarter Test (Checks 4/32 Inch)
The quarter test works exactly like the penny test, but it measures a safer threshold. The distance from a quarter’s edge to the top of Washington’s head is about 4/32 inch — double the penny’s depth, and the point where AAA recommends replacing tires.

Step 1: Hold a quarter with Washington’s head pointing down, upside down and facing you.
Step 2: Insert it head-first into a main tread groove and push it to the bottom.
Step 3: If the tread reaches the top of Washington’s head and covers it, you have more than 4/32 inch left. If you can see the top of his head, you are at or below 4/32 inch. Start shopping for new tires now, even though the tire is still technically legal.
Step 4: Repeat across the tire and on all four tires, and go by the lowest reading.
Think of the two coin tests as a pair: the quarter says “start shopping,” and the penny says “stop driving on these in the rain.” A tire that passes the penny test but fails the quarter test will let you down in the first heavy rainstorm — legal, but already a safety problem. See AAA’s report on worn tires for the full test results.
Method 3: Check the Wear Bars (No Tools Needed)
Almost every tire sold in the US has tread wear indicator bars molded into the grooves — small raised bridges of rubber running across the groove at exactly 2/32 inch high. When the surrounding tread wears down to the same height as those bars, the tire has reached the legal limit.
Step 1: Find the bars. Look down into the main grooves for the little raised bridges across them. The sidewall triangle or “TWI” marking lines up with where a bar sits.
Step 2: Compare the bar to the tread around it. If the bar still sits noticeably below the surrounding tread surface, you have life left. If the tread surface on either side is flush with the bar, so the groove looks like it has a smooth rubber bridge across it, the tire is at 2/32 inch and is done.

Step 3: Check several bars around the tire. Wear is rarely even, so one bar can look fine while another is already flush.
Wear bars share the penny test’s limitation: they only flag 2/32 inch, not the 4/32 inch point where you should start planning a replacement. Treat a flush wear bar as a hard stop.
Method 4: Use a Tread Depth Gauge (The Exact Number)
If you want a real number instead of a pass/fail, buy a tread depth gauge. The simple pencil-style gauges cost about $3–$10 at any auto parts store, need no batteries, and work fine. Dial and digital gauges cost a little more and are easier to read, but they are not required.
Step 1: Zero the gauge if needed. On a pencil gauge, set the base on a flat surface and make sure the reading is at zero.
Step 2: Push the probe into a main groove until it reaches the bottom. Keep the gauge straight — held at an angle, it reads deeper than the tire really is.
Step 3: Press the base flat against the tread, level on the tread blocks on either side of the groove. Read the measurement in 32nds of an inch (most gauges also show millimeters).

Step 4: Measure at least three spots across each tire — inner, center, and outer — and at two or three positions around it. Write the numbers down for all four tires and go by the lowest reading.
Only a gauge lets you track wear over time: 7/32 inch today and 5/32 inch in six months tells you your wear rate. Keep it in your glove box and use it every time you check your pressure.
Tire Tread Depth Chart: What Each Reading Means
| Tread depth | In mm | Status | What to do |
|---|---|---|---|
| 10/32–11/32 inch | 7.9–8.7 mm | New | Full tread — just check monthly |
| 8/32–9/32 inch | 6.4–7.1 mm | Good | Barely worn — recheck monthly |
| 6/32–7/32 inch | 4.8–5.6 mm | Acceptable | Fine for dry and wet driving; if you drive in snow, start shopping |
| 4/32–5/32 inch | 3.2–4.0 mm | Replace soon | Wet grip significantly degraded — AAA recommends replacing at 4/32 inch |
| 3/32 inch | 2.4 mm | Nearly worn out | Dangerous in rain — replace immediately |
| 2/32 inch or less | 1.6 mm or less | Legal limit | Replace today — bald in the rain, and will fail inspection |

At 6/32 inch or more, keep driving and recheck monthly. At 4/32 inch, start shopping — wet performance has already dropped sharply. At 2/32 inch, replace the tire today.
If you drive in snow, replace sooner — snow traction fades earlier than wet grip. Our guide to all-season vs winter tires explains the trade-offs.
Where and How Often to Measure
How often: Check at least once a month, at the same time you check tire pressure — NHTSA recommends this monthly cadence. Also check before any long road trip, and more often once tread reaches 4/32 inch. Check right away if the car pulls to one side, vibrates, or shows visibly uneven wear.
Where: Measure in the main grooves at three points across the tread — inner, center, and outer — and at two or three positions around the tire.
Which tires: All four, plus the spare if you have a full-size one. Front tires usually wear faster than rears on front-wheel-drive cars. Write the numbers down by position so you can compare them next time.
Reading Uneven Wear: What Your Tires Are Telling You
While you are down there checking depth, look at where the tread is wearing. The pattern often points straight at the cause.

Both edges worn, center fine — under-inflation. A soft tire flexes too much and rides on its shoulders. Fix the pressure to the number on your door jamb sticker (not the maximum on the sidewall). See what tire numbers mean for the sidewall markings.
Center worn, edges fine — over-inflation. A hard tire bulges in the middle, so the center strip does most of the work. Let air out to the recommended pressure — more air is not better.
One side worn more than the other — alignment. This usually points to a camber or toe problem that no pressure adjustment will fix. Get an alignment before new tires go on, or the new set will wear the same way. See tire balancing vs alignment.
Scalloped dips around the tire (cupping) — suspension. Worn shocks or struts let the tire bounce as it rolls, carving scoops into the tread. Have the suspension inspected; rotating the tires will not stop it.
Catching uneven wear early saves money: a pressure fix costs nothing, and an alignment costs far less than a new set of tires worn out on one edge. Regular rotation also evens out wear — see how often to rotate tires and the tire rotation pattern.
When to Replace Your Tires: The Verdict
- 2/32 inch — replace immediately. The legal minimum in most states, the point where the tread is flush with the wear bars, and the point where the penny test fails. The tire is bald for practical purposes, especially in the rain.
- 4/32 inch — replace soon. AAA’s recommended threshold, and the quarter test’s line. Wet braking is already 43% worse than new at this depth. Start shopping now, and replace before the rainy season — not after your first skid.
- 6/32 inch or more — keep driving. Recheck monthly. If you drive in snow, start thinking about replacements sooner, since snow grip fades earlier than wet grip.
But depth is not the only reason to retire a tire. Replace one right away — even with tread left — if you see visible cords, a bulge on the sidewall, deep cracks, a sidewall puncture, or repeated unexplained air loss. Age matters too: most manufacturers recommend replacing tires after six to ten years regardless of tread. Check the four-digit DOT date code on the sidewall for the week and year of manufacture.
If you are unsure whether a tire is safe, do not guess — a tire shop will measure your tread for free in most cases. For the full list of warning signs, see when to change tires.
The Bottom Line
Checking tire tread depth takes two minutes, costs nothing, and can keep you out of a crash. The quarter test is the one to remember: if you can see the top of Washington’s head, you are at or below 4/32 inch, and it is time to start shopping for new tires. The penny test is your deadline: if you can see the top of Lincoln’s head, you are at or below the 2/32 inch legal minimum, and the tire needs replacing today.
Do not wait for your tires to look bald. Check them once a month, go by the lowest reading you find, and replace at 4/32 inch if you drive in rain or snow. Your brakes can be perfect and your car can have every safety system in the world — if the tires cannot grip, none of it matters.
Frequently Asked Questions
What is the minimum legal tire tread depth in the US?
In most US states, the legal minimum tire tread depth is 2/32 of an inch (about 1.6 mm). At that depth the tread is flush with the built-in wear bars, and the tire must be replaced. A few states have no numeric standard, so check your own state’s rule, but 2/32 inch is the practical floor everywhere.
How do I check tire tread depth with a penny?
Insert a penny into a main tread groove with Lincoln’s head pointing down into the tire. If the tread covers the top of his head, you have more than 2/32 inch left. If you can see all of his head, your tread is at or below 2/32 inch and the tire needs replacing now. Test several grooves on each tire and go by the shallowest reading.
Is 4/32 inch tire tread safe to drive on?
At 4/32 inch your tires are still legal, but wet grip is already seriously reduced. In AAA testing, tires worn to 4/32 inch needed 43% more distance to stop on wet pavement from 60 mph than new tires — about 87 extra feet for a passenger car. Treat 4/32 inch as the point to start shopping for replacements, especially if you drive in rain or snow.
What is the tread depth of a new tire?
Most new all-season passenger tires start at 10/32 to 11/32 inch of tread depth (about 8 to 9 mm). Winter tires and all-terrain truck tires often start deeper, while some high-performance summer tires start a little shallower, around 8/32 to 10/32 inch.
How often should I check my tire tread depth?
Check your tire tread depth at least once a month, at the same time you check tire pressure, and always before a long road trip. Check more often once your tread reaches 4/32 inch, and check right away if you notice pulling to one side, a new vibration, or visibly uneven wear.
Can I drive on tires with 2/32 inch of tread?
It is technically legal in most states, but it is not safe in wet weather. At 2/32 inch the grooves can no longer clear water effectively, so hydroplaning risk rises sharply and wet stopping distances grow dramatically. Treat 2/32 inch as replace today, not still fine — and if you drive in rain or snow regularly, replace at 4/32 inch instead.
